Make you own taiko controller with Arduino!
Go to file
2024-01-02 14:57:52 -08:00
ATmega32U4 Minor refactor and cleanup 2024-01-02 14:02:22 -08:00
ESP32 Minor refactor and cleanup 2024-01-02 14:02:22 -08:00
ESP32-S3 Minor pin number change 2024-01-02 14:57:52 -08:00
images Moved ESP32 to main branch 2023-12-24 18:40:11 -08:00
.gitignore Add delay mechanism back 2023-12-24 21:30:29 -08:00
LICENSE Initial commit 2016-03-21 20:44:54 +08:00
README_ja-JP.md Moved ESP32 to main branch 2023-12-24 18:40:11 -08:00
README_zh-CN.md Moved ESP32 to main branch 2023-12-24 18:40:11 -08:00
README.md Moved ESP32 to main branch 2023-12-24 18:40:11 -08:00

日本語のドキュメントはこちら

中文文档在这里

Taiko Drum Controller

Taiko Drum Controller - Arduino (ATmega32U4/ESP32)

Open-source hardware program to make your own Taiko no Tatsujin PC controller.

About this Project

This project aims to help you develop your own hardware taiko at home.

This program is for personal and non-commercial use only.

What You Need

  1. An Arduino Micro/Leonardo (ATmega32U4) board or an Arduino Nano ESP (ESP32) board.

    Most ATmega32U4 boards work, but you need to verify that they support keyboard emulation; ATmega328P boards like Arduino Uno don't work.

    ESP32 is strongly recommended because it's significantly more powerful than ATmega32U4. This project uses an ESP32-WROOM-32 board.

  2. 4 piezoelectric sensors.

  3. 8 100kΩ resistors.

  4. (Optional) 4 bridge rectifier chips such as DB107 (see the Additional Notes section for details).

  5. (Optional) Some red and blue LEDs.

  6. Necessary electronic components (breadboards and jumper wires, etc.).

  7. Wood planks and cutting tools (only if you need to make your physical taiko drum from scratch). If you have an aftermarket taiko or a Big Power Lv. 5 drum, you can use them directly.

Steps to Make the Controller

  1. Make the drum and firmly glue the 4 piezoelectric sensors to the drum. Refer to the image for preferred locations of the sensors.

    Sensor Setup

  2. Connect the piezoelectric sensors and other components to the controller as follows (the polarity of the piezoelectric sensors don't matter);

    The following schemes are for Arduino Micro boards. If you use a different board, refer to its documentations for the connection.

    Controller scheme

    If you choose to add the bridge rectifiers, use the following scheme:

    Controller scheme with bridge rectifiers

  3. Flash the firmware to the board.

    You may need to fine-tune some parameters like SAMPLE_CACHE_LENGTH, HIT_THRES, RESET_THRES, and sensitivity. See the following section for details.

  4. Have fun!

Tuning the Parameters

  1. Hit and reset threshold

    Set DEBUG 1 (this disables the keyboard output and sends signal values from the serial port), flash the firmware, roll on one of the 4 areas of the drum, and visualize the graph from the output of the serial monitor. The hit threshold should be lower than your heaviest hit on the drum, and the reset threshold should be greater than the trough between roll hits. The reset value should also be below the hit value.

    Repeat the process for the rest 3 areas and find the best one that fits all.

    Setting hit and reset values

  2. Sampling length

    For maximum runtime speed, the cache.h library has been optimized to work with SAMPLE_CACHE_LENGTH window sizes of powers of 2. That means 2, 8, 16, and 32, etc. Practically 16 is the best value for Arduino, but if you have a powerful microcontroller that samples the input at the speed of at least 4000Hz or more, you can change the value to 32 for a smoother (in other words, less noisy) curve.

  3. Sensitivities

    Not all piezoelectric sensors are the same, and due to installation errors, the captured signals from the 4 sensors may vary significantly. The sensitivity values are multipliers to normalize the differences. In the following example, the right-don area generates a much higher value than the rest 3, so you can adjust sensitivity to {1.0, 1.0, 0.5, 1.0} to eliminate the issue.

    Setting sensitivity values

    Note that the installation of the sensors is very critical. You should make sure that the sensors are firmly attached on the wood and located properly.

Additional Notes

  1. Why using bridge rectifiers

    Without biasing the voltage of the piezoelectric sensors, their output voltage range is about -5V to +5V. However, the ADCs of the analog inputs only accepts positive voltage values (0-3.3V for ESP32 and 0-5V for ATmega32U4). When they receive a negative voltage, it's simply truncated to 0.

    It's usually okay for normal electronic drums because we're just losing half of the input energy and it doesn't influence how we calculate the hitting time. But it can cause problems for taiko drums, especially with slow processors like ATmega32U4.

    In a taiko drum, all the 4 vibrating pieces are connected together, meaning that if you hit left-don, the processor also receives signals from left-kat, right-don, and right-kat. If the left-don piezoelectric sensor generates a negative voltage at the beginning and is truncated by the ADC, it will cause a minor "delay" of about 3 to 4 milliseconds, and the processor could incorrectly treat this hit as a right-don, a left-kat, or even a right-kat, whichever sends a highest positive value.

    Using a bridge rectifier, all negative values are converted to positive. In other words, it's like the abs() function, ensuring that we don't lose any negative voltages.

    Why using bridge rectifiers