diff --git a/Production/3DPrint/geki_pico_lever_fixer.stl b/Production/3DPrint/geki_pico_lever_fixer.stl index b3943e0..ba8f2a3 100644 Binary files a/Production/3DPrint/geki_pico_lever_fixer.stl and b/Production/3DPrint/geki_pico_lever_fixer.stl differ diff --git a/Production/3DPrint/geki_pico_lever_rotator_5mm.stl b/Production/3DPrint/geki_pico_lever_rotator_5mm.stl new file mode 100644 index 0000000..223a05e Binary files /dev/null and b/Production/3DPrint/geki_pico_lever_rotator_5mm.stl differ diff --git a/Production/3DPrint/geki_pico_lever_rotator_6mm .stl b/Production/3DPrint/geki_pico_lever_rotator_6mm .stl new file mode 100644 index 0000000..8bc14e5 Binary files /dev/null and b/Production/3DPrint/geki_pico_lever_rotator_6mm .stl differ diff --git a/Production/3DPrint/geki_pico_lever_shaft_5mm.stl b/Production/3DPrint/geki_pico_lever_shaft_5mm.stl deleted file mode 100644 index 487db48..0000000 Binary files a/Production/3DPrint/geki_pico_lever_shaft_5mm.stl and /dev/null differ diff --git a/Production/3DPrint/geki_pico_lever_shaft_6mm.stl b/Production/3DPrint/geki_pico_lever_shaft_6mm.stl deleted file mode 100644 index 6b2b8c0..0000000 Binary files a/Production/3DPrint/geki_pico_lever_shaft_6mm.stl and /dev/null differ diff --git a/Production/3DPrint/geki_pico_top.3mf b/Production/3DPrint/geki_pico_top.3mf index 7bbcdb7..9b472ea 100644 Binary files a/Production/3DPrint/geki_pico_top.3mf and b/Production/3DPrint/geki_pico_top.3mf differ diff --git a/README.md b/README.md index 79c473e..4ecc0d0 100644 --- a/README.md +++ b/README.md @@ -140,13 +140,13 @@ You need to rotate 135 degrees on Z axis to fit the bed. https://www.amazon.com/METALLIXITY-Double-Screws-Stainless-Threaded/dp/B0B7BX3CYH * 1x round magnet with **5mm** or **6mm** diameter, **2mm** to **3.5mm** tall, MUST be radially/diametrically magnetized (N-S poles on the curved side). https://wargameportal.com/products/special-diametrically-magnetized-50pcs-5mm-x-2mm-3-16-x-1-16-disc-magnets?variant=49014932209942 - * 6x **M2*5mm regular screws** for resistance adjustment. + * 6x **M2*6mm regular screws** for resistance adjustment. * 4x **M2*16mm regular screws** for fixing the bearings. - * Optional: Some keyboard switch lubricant. + * Optional: Some damping grease. * Assemble Steps 1. Print out the parts. - 2. Stick PTFE/UHMW tape to the sliding surfaces of the fixer and the shaft. Then trim the tape to match the surface shape. If you have some keyboard switch lubricant, apply a tiny bit on the sliding surfaces. Turn the M2*5mm screws into the bearing fixers halfway, don’t and never tighten them. + 2. Stick PTFE/UHMW tape to the sliding surfaces of the fixer and the shaft. Then trim the tape to match the surface shape. If you have some damping grease (medium or medium-high stickiness), apply a tiny bit on the sliding surfaces. Turn the M2*6mm screws into the bearing fixers halfway, don’t and never tighten them. 3. Install the 2 bearings on both sides of the shaft and put it in the base, then use M2*16mm screws to fix the two bearing fixers on the base. diff --git a/README_CN.md b/README_CN.md index bfbf205..ae4ba32 100644 --- a/README_CN.md +++ b/README_CN.md @@ -140,14 +140,14 @@ https://www.amazon.com/METALLIXITY-Double-Screws-Stainless-Threaded/dp/B0B7BX3CYH * 1x 圆形小磁铁，直径 **5mm** 或者 **6mm**，厚度 **2mm** 到 **3.5mm**，必须是径向充磁的，也就是磁铁两极是在圆弧面上。 https://wargameportal.com/products/special-diametrically-magnetized-50pcs-5mm-x-2mm-3-16-x-1-16-disc-magnets?variant=49014932209942 - * 6x **M2*5mm 螺丝** 用于阻尼调整。 + * 6x **M2*6mm 螺丝** 用于阻尼调整。 * 4x **M2*16mm 螺丝** 用于固定轴承。 - * 可选: 键轴润滑剂。 + * 可选: 阻尼脂。 * 组装过程 1. 打印相关的零件 - 2. 把 PTFE/UHMW 胶带贴在摇杆和轴的滑动表面上，然后大致修剪成相应的形状。如果你有键盘轴润滑剂，可以在滑动表面涂一丁点。然后把 M2*5mm 螺丝半拧入轴承固定器，注意不要拧紧。 + 2. 把 PTFE/UHMW 胶带贴在摇杆和轴的滑动表面上，然后大致修剪成相应的形状。如果你有中或中高粘度的阻尼脂，可以在滑动表面涂一丁点。然后把 M2*6mm 螺丝半拧入轴承固定器，注意不要拧紧。 3. 把 2 个轴承固定器固定在底座上，然后用 M2*16mm 螺丝固定轴承。