133 lines
3.4 KiB
C++
133 lines
3.4 KiB
C++
#include "Aime_Reader.h"
|
||
|
||
// 该定义存在时，使用 115200 波特率，型号为 837-15396
|
||
|
||
#define high_baudrate
|
||
|
||
// 该定义存在时，跳过实际的 FeliCa 操作
|
||
// 仅通过 CMD_CARD_DETECT 发送 IDm、PMm、SystemCode
|
||
#define SKIP_FeliCa_THROUGH
|
||
|
||
|
||
|
||
void setup() {
|
||
FastLED.addLeds<NEOPIXEL, LED_PIN>(leds, NUM_LEDS);
|
||
FastLED.setBrightness(50);
|
||
FastLED.showColor(0);
|
||
nfc.begin();
|
||
while (!nfc.getFirmwareVersion()) { // 检测不到 PN532 时，循环红灯闪烁，不再继续初始化
|
||
FastLED.showColor(0xFF0000);
|
||
delay(500);
|
||
FastLED.showColor(0);
|
||
delay(500);
|
||
}
|
||
nfc.setPassiveActivationRetries(0x10);
|
||
nfc.SAMConfig();
|
||
// 初始化数据包结构体对象
|
||
memset(req.bytes, 0, sizeof(req.bytes));
|
||
memset(res.bytes, 0, sizeof(res.bytes));
|
||
|
||
SerialDevice.begin(baudrate);
|
||
FastLED.showColor(BootColor);
|
||
}
|
||
|
||
void loop() {
|
||
// 从串口读取数据，数据校验成功后，跳转到对应的函数执行操作
|
||
switch (packet_read()) {
|
||
case 0: // 数据包未读取完成
|
||
break;
|
||
|
||
case CMD_TO_NORMAL_MODE:
|
||
sys_to_normal_mode();
|
||
break;
|
||
case CMD_GET_FW_VERSION:
|
||
sys_get_fw_version();
|
||
break;
|
||
case CMD_GET_HW_VERSION:
|
||
sys_get_hw_version();
|
||
break;
|
||
|
||
// 读卡和 PN532 操作
|
||
case CMD_START_POLLING:
|
||
nfc_start_polling();
|
||
break;
|
||
case CMD_STOP_POLLING:
|
||
nfc_stop_polling();
|
||
break;
|
||
case CMD_CARD_DETECT:
|
||
nfc_card_detect();
|
||
break;
|
||
|
||
// MIFARE 处理
|
||
case CMD_MIFARE_KEY_SET_A: // 设置 MIFARE keyA
|
||
memcpy(KeyA, req.key, 6);
|
||
res_init();
|
||
break;
|
||
|
||
case CMD_MIFARE_KEY_SET_B: // 设置 MIFARE keyB
|
||
res_init();
|
||
memcpy(KeyB, req.key, 6);
|
||
break;
|
||
|
||
case CMD_MIFARE_AUTHORIZE_A:
|
||
nfc_mifare_authorize_a();
|
||
break;
|
||
|
||
case CMD_MIFARE_AUTHORIZE_B:
|
||
nfc_mifare_authorize_b();
|
||
break;
|
||
|
||
case CMD_MIFARE_READ:
|
||
nfc_mifare_read();
|
||
break;
|
||
|
||
#ifndef SKIP_FeliCa_THROUGH
|
||
// FeliCa 读写
|
||
case CMD_FELICA_THROUGH:
|
||
nfc_felica_through();
|
||
break;
|
||
#endif
|
||
|
||
// LED
|
||
case CMD_EXT_BOARD_LED_RGB: // 设置 LED 颜色，无需回复
|
||
FastLED.showColor(CRGB(req.color_payload[0], req.color_payload[1], req.color_payload[2]));
|
||
break;
|
||
|
||
case CMD_EXT_BOARD_INFO:
|
||
sys_get_led_info();
|
||
break;
|
||
|
||
case CMD_EXT_BOARD_LED_RGB_UNKNOWN: // 未知，仅在使用 emoney 时出现
|
||
break;
|
||
|
||
case CMD_CARD_SELECT:
|
||
case CMD_CARD_HALT:
|
||
case CMD_EXT_TO_NORMAL_MODE:
|
||
case CMD_TO_UPDATER_MODE:
|
||
res_init();
|
||
break;
|
||
case CMD_FIRMWARE_UPDATE:
|
||
res_init();
|
||
res.status = STATUS_FIRM_UPDATE_SUCCESS;
|
||
//当读卡器发送的FW版本与amdaemon要求的版本不一致时，
|
||
//游戏会发送0x60使读卡器进入update模式，再通过0x64再次更新，
|
||
//此时需要回复0x08方可再次跳过更新
|
||
break;
|
||
case CMD_SEND_HEX_DATA: // 非 TN32MSEC003S 时，可能会触发固件更新逻辑
|
||
res_init();
|
||
res.status = STATUS_COMP_DUMMY_3RD;
|
||
// 读卡器HW版本是837-15286时应该回复0x10, 837-15396回复0x20
|
||
break;
|
||
|
||
case STATUS_SUM_ERROR: // 读取数据校验失败时的回复，未确认效果
|
||
res_init();
|
||
res.status = STATUS_SUM_ERROR;
|
||
break;
|
||
|
||
default: // 对于其他未知的数据默认处理方式，未确认效果
|
||
res_init();
|
||
res.status = STATUS_INVALID_COMMAND;
|
||
}
|
||
packet_write();
|
||
}
|