Added some filed and updated the readme and globalc.cpp

README.md

@@ -99,14 +99,22 @@ JCM from the Discord explained the process pretty good:
    5. Reccomended is 3 sensors on the bottom middle of plate all with 3 different refernece resistor values for accuracy across all temperature ranges and 1 thermistor held by a pair of helping hangs placed so the head touches somewhere on the PCB to be refllowed
    By default this is set as thermistor 1:
 
-   Here are the defualt thermistor settings: 
+   *** IMPORTANT: Thermistors 1 is ONLY available on the hotplate. Thermistor 6 is only available on the controller via connector 5**
 
-   - Thermistor thermistor1(THERMISTOR1_PIN, 2545 , ThermistorZ_Placement::ON_PCB, ThermistorXY_Placement::MIDDLE); -> 2545Kohm set refrence
-   - Thermistor thermistor2(THERMISTOR2_PIN, 2125, ThermistorZ_Placement::BOTTOM, ThermistorXY_Placement::MIDDLE); - > 2125Kohm set refrence
-   - Thermistor thermistor3(THERMISTOR3_PIN, 9100, ThermistorZ_Placement::BOTTOM, ThermistorXY_Placement::MIDDLE_LOW_TEMP); -> 9100Kohm set refrence
-   - Thermistor thermistor4(THERMISTOR4_PIN, 564, ThermistorZ_Placement::BOTTOM, ThermistorXY_Placement::MIDDLE_HIGH_TEMP);-> 564Kohm set refrence
 
-   The set resistence is measured between a GND point anywhere on the board and the LEFT pin of the connector with the thermistor UNPLUGGED
+   You can solder the thermistors directly on the hotplatte or use them with the connector. Please update the thermistor settings to the way you have them set-up.
+
+   Here are the defualt thermistor settings, The assume that the thermistors are soldered on the plate for 1,2,3: 
+   Thermistors 6 on the connector number 5, touching the PCB to be soldered.
+
+   - Thermistor thermistor1(THERMISTOR2_PIN, 2125, ThermistorZ_Placement::BOTTOM, ThermistorXY_Placement::MIDDLE); //- > 2125Kohm set refrence
+   - Thermistor thermistor2(THERMISTOR3_PIN, 9100, ThermistorZ_Placement::BOTTOM, ThermistorXY_Placement::MIDDLE_LOW_TEMP);// -> 9100Kohm set refrence
+   - Thermistor thermistor3(THERMISTOR4_PIN, 564, ThermistorZ_Placement::BOTTOM, ThermistorXY_Placement::MIDDLE_HIGH_TEMP);//-> 564Kohm set refrence
+   - Thermistor thermistor6(THERMISTOR1_PIN, 2545 , ThermistorZ_Placement::ON_PCB, ThermistorXY_Placement::MIDDLE);// -> 2545Kohm set refrence -> This thermistor is set directly touching the PCB to be soldered
+
+   If you wish to only use the connectors use 2,3,4 and update the Globals .cpp to match your settings
+      
+   The set resistence is measured between a GND point anywhere on the board and the LEFT pin of the connector with the thermistor UNPLUGGED and the MODULE POWERED OFF!!!!
 
    you can measure and set those to the preset values or modify the values in globals.ccp to match your thermistors.
 

src/globals.cpp

@@ -31,15 +31,17 @@ TempCalibration calibration_100K_3950 = {25, 100000, 107, 4957, 167, 1000};
 // To measure the resistence turn off the controller completley and measure between GND and the left pin of the connector with the thermistor unplugged
 
 // 2.5k reference = Best accuracy around 138C
-Thermistor thermistor1(THERMISTOR1_PIN, 2545 , ThermistorZ_Placement::ON_PCB, ThermistorXY_Placement::MIDDLE);
-Thermistor thermistor2(THERMISTOR2_PIN, 2125, ThermistorZ_Placement::BOTTOM, ThermistorXY_Placement::MIDDLE);
-Thermistor thermistor3(THERMISTOR3_PIN, 9100, ThermistorZ_Placement::BOTTOM, ThermistorXY_Placement::MIDDLE_LOW_TEMP);
-// 1k reference = Best accuracy around 173c
+
+    Thermistor thermistor1(THERMISTOR2_PIN, 2125, ThermistorZ_Placement::BOTTOM, ThermistorXY_Placement::MIDDLE); //- > 2125Kohm set refrence
+    Thermistor thermistor2(THERMISTOR3_PIN, 9100, ThermistorZ_Placement::BOTTOM, ThermistorXY_Placement::MIDDLE_LOW_TEMP);// -> 9100Kohm set refrence//// 9k reference = Best accuracy around 90C -> This thermistor is used for the preheat phase if attached
+    Thermistor thermistor3(THERMISTOR4_PIN, 564, ThermistorZ_Placement::BOTTOM, ThermistorXY_Placement::MIDDLE_HIGH_TEMP);//-> 564Kohm set refrence // 564R reference = Best accuracy around 210C
+    Thermistor thermistor6(THERMISTOR1_PIN, 2545 , ThermistorZ_Placement::ON_PCB, ThermistorXY_Placement::MIDDLE);// -> 2545Kohm set refrence -> This thermistor is set directly touching the PCB to be soldered
+
+// Unused by defualt, keep unplugged
     Thermistor thermistor4(THERMISTOR4_PIN, 564, ThermistorZ_Placement::BOTTOM, ThermistorXY_Placement::MIDDLE_HIGH_TEMP);
-// 515R reference = Best accuracy around 210C
     Thermistor thermistor5(THERMISTOR5_PIN,5727, ThermistorZ_Placement::TOP, ThermistorXY_Placement::MIDDLE_LOW_TEMP);
-// 9k reference = Best accuracy around 90C -> This thermistor is used for the preheat phase if attached
-Thermistor thermistor6(THERMISTOR6_PIN, 467, ThermistorZ_Placement::TOP, ThermistorXY_Placement::MIDDLE_HIGH_TEMP);
+
+
 
 //---------------------------------------------------------------------------------------------------------------------------------------
 
@@ -51,7 +53,6 @@ Thermistor thermistors[6] = {thermistor1, thermistor2, thermistor3, thermistor4,
 
 
 // Which Color to use for the reflow process markers
-
 uint16_t preheat_COLOR = 0x6800;
 uint16_t soak_COLOR = 0x6b60;
 uint16_t reflow_COLOR = 0x0201;