Added Z and XY coordinates for Thermistor placment

src/globals.cpp

@@ -8,6 +8,9 @@ AnalogRef analogRef(5.0);
 TempCalibration calibration_100K_3950 = {25, 100000, 86, 10324, 169, 1148};
 // Initalize the 3950 100K thermistors with ACTUAL reference resistor measurnment(Measured between Left pin and GND when the board is powered off) using the default calibration data for 100K thermistor
 
+// You can also make a custom calibration data for your thermistor and use that instead of the default one pass it as shown below --> keep the naming of the thermistor the same as the one you are replacing
+//Thermistor thermistor1(THERMISTOR1_PIN, 100000, calibration_100K_3950,ThermistorZ_Placement::TOP,ThermistorXY_Placement::MIDDLE);
+
 
 //--------------------------------------------------------------------------------------------------------------------------------------
 
@@ -15,17 +18,19 @@ TempCalibration calibration_100K_3950 = {25, 100000, 86, 10324, 169, 1148};
 
 //You can tweak them from the datasheet to best fit your thermistor but we reccoemnd using the default values and setting the potentiometer to these values
 // Does not have to be perfect just set it close to this value and record the measured value and put it for the thermistors
+//To measure the resistence turn off the controller completley and measure between GND and the left pin of the connector with the thermistor unplugged
 
 //2.5k reference = Best accuracy around 138C
-Thermistor thermistor1(THERMISTOR1_PIN, 2500);
+Thermistor thermistor1(THERMISTOR1_PIN, 2500,ThermistorZ_Placement::TOP,ThermistorXY_Placement::MIDDLE);
-Thermistor thermistor2(THERMISTOR2_PIN, 2500);
+Thermistor thermistor2(THERMISTOR2_PIN, 2500,ThermistorZ_Placement::TOP,ThermistorXY_Placement::MIDDLE);
-Thermistor thermistor3(THERMISTOR3_PIN, 2500);
+Thermistor thermistor3(THERMISTOR3_PIN, 2500,ThermistorZ_Placement::TOP,ThermistorXY_Placement::MIDDLE);
 //1k reference = Best accuracy around 173c
-Thermistor thermistor4(THERMISTOR4_PIN, 1000);
+Thermistor thermistor4(THERMISTOR4_PIN, 1000,ThermistorZ_Placement::TOP,ThermistorXY_Placement::MIDDLE);
 //515R reference = Best accuracy around 210C
-Thermistor thermistor5(THERMISTOR5_PIN, 515);
+Thermistor thermistor5(THERMISTOR5_PIN, 515,ThermistorZ_Placement::TOP,ThermistorXY_Placement::MIDDLE);
 //9k reference = Best accuracy around 90C -> This thermistor is used for the preheat phase if attached
-Thermistor thermistor6(THERMISTOR6_PIN, 9000);
+Thermistor thermistor6(THERMISTOR6_PIN, 9000,ThermistorZ_Placement::TOP,ThermistorXY_Placement::MIDDLE);
+
 
 //---------------------------------------------------------------------------------------------------------------------------------------
 
@@ -65,6 +70,7 @@ ReflowProfile reflowProfiles[] = {
 
  
 };
+
 //---------------------------------------------------------------------------------------------------------------------------------------
 
 ReflowProfile chosenReflowProfile = reflowProfiles[0];

src/thermistors/Thermistor.cpp

@@ -55,7 +55,8 @@ float Thermistor::getResistance()
     // Get resistance value
     float buffer = raw * systemVoltage;
     float vOut = (buffer) / 1023;
-    // Serial.println(vOut);
+
+    //Calculate the resistance of the thermistor with the system voltage accounted for
     buffer = (systemVoltage / vOut) - 1;
 
     // return the resistence

src/thermistors/Thermistor.h

@@ -21,7 +21,6 @@ struct TempCalibration
     float highR;
 };
 
-
 extern TempCalibration calibration_100K_3950;
 
 #define THERMISTOR1_PIN 39
@@ -35,17 +34,32 @@ extern AnalogRef analogRef;
 
 // Include any necessary libraries here
 
+enum ThermistorZ_Placement
+{
+    TOP,
+    BOTTOM
+};
+
+enum ThermistorXY_Placement
+{
+    MIDDLE,
+    LEFT,
+    RIGHT
+};
+
 class Thermistor
 {
 public:
     // Constructor
     Thermistor();
 
-    Thermistor(uint8_t pin, uint16_t resistance, TempCalibration calibration): thermistorPin(pin), setRes(resistance), calibration(calibration) {
+    Thermistor(uint8_t pin, uint16_t resistance, TempCalibration calibration,ThermistorZ_Placement zPlacement,ThermistorXY_Placement  xyPlacment) : thermistorPin(pin), setRes(resistance), calibration(calibration),zPlacement(zPlacement),xyPlacment(xyPlacment)
+    {
         calculateCoefficents(calibration);
     }
 
-    Thermistor(uint8_t pin, uint16_t resistance): thermistorPin(pin), setRes(resistance), calibration(calibration_100K_3950) {
+    Thermistor(uint8_t pin, uint16_t resistance,ThermistorZ_Placement zPlacement,ThermistorXY_Placement  xyPlacment) : thermistorPin(pin), setRes(resistance), calibration(calibration_100K_3950),zPlacement(zPlacement),xyPlacment(xyPlacment)
+    {
         calculateCoefficents(calibration);
     }
 
@@ -58,6 +72,8 @@ public:
     void calculateCoefficents(TempCalibration calibration);
 
 private:
+    ThermistorZ_Placement zPlacement;
+    ThermistorXY_Placement xyPlacment;
     const double K = 273.15;
     float sensorResistance;
     uint8_t thermistorPin;