mirror of
https://gitea.tendokyu.moe/tasoller/host-aprom.git
synced 2024-11-12 01:10:49 +01:00
71 lines
2.5 KiB
Markdown
71 lines
2.5 KiB
Markdown
# TASOLLER Custom Firmware (Host MCU - Application ROM)
|
|
|
|
See [Development](./Development.md) for development information.
|
|
|
|
Yes, the code is a mess. I just wanted to get something onto git y'know :).
|
|
|
|
## Setup
|
|
### Installing Firmware
|
|
- Disconnect the PC cable from the TASOLLER
|
|
- Hold down the FN2 button, while reconnecting the PC cable
|
|
- `HOSTMCU` should show as a device
|
|
- Use `Update V1.1.exe` from official firmware updates to load the firmware
|
|
|
|
Currently, Dao CFW is required on the LED board. This is controlled by `LED_FIRMWARE_CFW` in `src/led.h`.
|
|
|
|
### Configuring segatools
|
|
This firmware emulates arcade IO. As such, segatools' emulation should be disabled, by adding the following lines:
|
|
|
|
```ini
|
|
[slider]
|
|
enable=0
|
|
[io4]
|
|
enable=0
|
|
```
|
|
|
|
Ensure no other `[slider]` section exists in the file (or if it does, set `enable=0` there instead).
|
|
|
|
The slider **MUST** be assigned to port `COM1`. To do this:
|
|
|
|
- Go to `Devices and Printers` in control panel
|
|
- Double click `TASOLLER`
|
|
- In the `Hardware` tab, double click `USB Serial Device`
|
|
- If this already reads `USB Serial Device (COM1)` nothing needs done
|
|
- Click `Change settings`
|
|
- Go to `Port Settings` -> `Advanced...`
|
|
- Under the dropdown for `COM Port Number:` select `COM1`
|
|
|
|
If `COM1` is already in use, check what device it is assigned to in Device Manager under `Ports (COM & LPT)`. You may need to enable `View` -> `Show hidden devices`.
|
|
|
|
Pre-chusan Chunithm uses IO3. This firmware does not (and unfortunately cannot) support IO3. It is recommended to enable the HID keyboard mode, and continue to use keyboard input for IRs.
|
|
|
|
## Controls
|
|
### General
|
|
Tap FN1 to insert a coin. FN2 is currently unbound.
|
|
|
|
### Configuration
|
|
While holding FN1, the following configuration options are available:
|
|
|
|
|
|
|
|
※ "Insert card" will hold the Enter key for 5 seconds
|
|
|
|
### Test menu
|
|
|
|
To enter the system test menu, double-tap FN2. This will mirror the on-screen controls, and additionally adds controls for the TEST and SERVICE buttons on a real cabinet. Double-tap FN2 again to leave this mode on the controller (note that this is not synced with the game exiting the menu!).
|
|
|
|
|
|
|
|
To access the TEST and SERVICE buttons without entering the test menu, hold FN2 instead.
|
|
|
|
|
|
|
|
## Keyboard Mapping
|
|
When the HID keyboard is enabled, the following mapping (UMIGURI defaults) is used:
|
|
|
|
|
|
|
|
with the airs mapped as `0OLP,.`.
|
|
|
|
Please note that this is slightly different to stock firmware!
|