f8adaa067f
Fill in lights mappings. Yes, I tested these on my own cabinet because I had to build a breakout cable to connect everything to essentially any other hardware than the stock fusion PCB. Breakout cable instructions and mappings also included as a bonus, since this is likely the use-case one might be looking for those pinouts.
4.7 KiB
Dancing Stage Fusion dedicated cabinet JAMMA edge wiring
The Dancing Stage Fusion dedicated cabinet has different wiring than classic Dancing Stage/Dance Dance Revoluion Machines that are either based on 573 analog/digital hardware or Python 2 hardware.
The cabinet connects to the main PCB using two JAMMA edge 28-pin connectors.
The following sub-sections provide full pinouts taken from a stock
Dancing Stage Fusion dedicated cabinet. NC denotes to "not connected".
Pinout primary 28-pin connector
This 28-pin connector is actually following the JAMMA specification.
Top side pinout
1: NC
2: GND
3: +5V
4: +5V
5: NC
6: +12V
7: NC
8: NC
9: NC
10: NC
11: NC
12: Video red
13: Video blue
14: Video GND
15: Test switch
16: Coin switch
17: P1 start
18: P1 up
19: P1 down
20: P1 left
21: P1 right
22: NC
23: P1 left select
24: P1 right select
25: NC
26: NC
27: NC
28: GND
Bottom side pinout
1: GND
2: GND
3: NC
4: NC
5: NC
6: +12V
7: NC
8: NC
9: NC
10: NC
11: NC
12: Video green
13: Video sync
14: Service switch
15: NC
16: NC
17: P2 start
18: P2 up
19: P2 down
20: P2 left
21: P2 right
22: NC
23: P2 select left
24: P2 select right
25: NC
26: NC
27: GND
28: GND
Pinout secondary 28-pin connector
This 28-pin connector is the same as the primary connector but does not follow the JAMMA pinout specification.
The follow hardware is connected on this connector:
- +5V power source
- Serial cable to EXT I/O
- Lights I/O cable to AMP box
Top side pinout
1: NC
2: NC
3: +5V (red)
4: NC
5: Jumper cable (brown) -> Connects to bottom pin 6
6: NC
7: EXT I/O serial TX (purple)
8: NC
9: NC
10: NC
11: NC
12: NC
13: NC
14: NC
15: NC
16: NC
17: NC
18: NC
19: NC
20: NC
21: NC
22: NC
23: NC
24: Lights P2 cabinet button lights (yellow-grey)
25: Lights P1 halo up (light blue)
26: Lights P2 halo down (grey)
27: GND for +5V (black)
28: NC
Bottom side pinout
1: NC
2: NC
3: NC
4: NC
5: NC
6: Jumper cable (brown) -> Connects to top pin 5
7: EXT I/O serial RX (grey)
8: EXT I/O serial GND (black)
9: NC
10: NC
11: NC
12: NC
13: NC
14: NC
15: NC
16: NC
17: NC
18: NC
19: NC
20: NC
21: NC
22: NC
23: Lights P1 cabinet button lights (purple-grey)
24: Lights P2 halo up (green)
25: Lights P1 halo down (purple)
26: Lights GND (black)
27: NC
28: NC
Lights I/O connector
Lights I/O connector that goes into the AMP box. Pintout order: looking at the front of the connector, left to right:
| |--| |
|-----------------|
|1 2 3 4 5 6 7 8 9|
|-----------------|
1: Earth (yellow-green)
2: P2 halo down (grey)
3: P1 halo down (purple)
4: P1 halo up (light blue)
5: P2 halo up (green)
6: P2 cabinet button lights (yellow-grey)
7: P1 cabinet button lights (purple-grey)
8: NC
9: GND (black)
EXT I/O serial connector
Serial connector going to the EXT I/O board. Pintout order: looking at the front of the connector, left to right:
| |
|-----|
|1 2 3|
|-----|
1: GND (black)
2: TX (purple)
3: RX (grey)
Adapter secondary JAMMA connector to "classic" DDR wiring
With the secondary JAMMA connector being propriatary to the Dancing Stage Fusion cabinet, you need a "breakout" adapter that splices the JAMMA connector into the following separate connectors:
EHR-5connector to COM1 on the PCB for the EXTIO- +5V supply, likely via a 2-pin connector that works with your cabinet's internal power infrastructure
XMP-11Vconnector to PORT1 on the PCB for lights
Note: Bass lights, P1/P2 pad lights as well as sensor multiplexing is handled by the EXTIO board.
COM1 breakout
Pinout for the EHR-5 connector breaking out of the JAMMA connector.
Pintout order for EHR-5: looking at the front of the connector,
left to right:
| |
|---------|
|1 2 3 4 5|
|---------|
1: GND (black)
2: NC
3: NC
4: RX (grey)
5: TX (purple)
Mapping for breakout cable:
JAMMA top: 7 -> EHR-5: 5
JAMMA bottom: 7 -> EHR-5: 4
JAMMA bottom: 8 -> EHR-5: 1
Lights connector breakout
Pinout for the XMP-11V connector breaking out of the JAMMA connector.
Pintout order for XMP-11V: looking at the front of the connector,
left to right:
| |--| |
|-----------------------|
|1 2 3 4 5 6 7 8 9 10 11|
|-----------------------|
1: NC
2: P1 halo up
3: P1 halo down
4: P2 halo up
5: P2 halo down
6: GND
7: NC
8: NC
9: P2 cabinet button lights
10: P1 cabinet button lights
11: GND
Mapping for breakout cable:
JAMMA top: 24 -> XMP-11V: 9
JAMMA top: 25 -> XMP-11V: 2
JAMMA top: 26 -> XMP-11V: 5
JAMMA bottom: 23 -> XMP-11V: 10
JAMMA bottom: 24 -> XMP-11V: 4
JAMMA bottom: 25 -> XMP-11V: 3
JAMMA bottom: 26 -> XMP-11V: 6 + 11