mirror of
https://github.com/Shizmob/arcade-docs.git
synced 2024-12-21 02:45:53 +01:00
f8adaa067f
Fill in lights mappings. Yes, I tested these on my own cabinet because I had to build a breakout cable to connect everything to essentially any other hardware than the stock fusion PCB. Breakout cable instructions and mappings also included as a bonus, since this is likely the use-case one might be looking for those pinouts.
276 lines
4.7 KiB
Markdown
276 lines
4.7 KiB
Markdown
# Dancing Stage Fusion dedicated cabinet JAMMA edge wiring
|
|
|
|
The Dancing Stage Fusion dedicated cabinet has different wiring than
|
|
classic Dancing Stage/Dance Dance Revoluion Machines that are either based
|
|
on 573 analog/digital hardware or Python 2 hardware.
|
|
|
|
The cabinet connects to the main PCB using two JAMMA edge 28-pin connectors.
|
|
|
|
The following sub-sections provide full pinouts taken from a stock
|
|
Dancing Stage Fusion dedicated cabinet. `NC` denotes to "not connected".
|
|
|
|
## Pinout primary 28-pin connector
|
|
|
|
This 28-pin connector is actually following the JAMMA specification.
|
|
|
|
### Top side pinout
|
|
|
|
```text
|
|
1: NC
|
|
2: GND
|
|
3: +5V
|
|
4: +5V
|
|
5: NC
|
|
6: +12V
|
|
7: NC
|
|
8: NC
|
|
9: NC
|
|
10: NC
|
|
11: NC
|
|
12: Video red
|
|
13: Video blue
|
|
14: Video GND
|
|
15: Test switch
|
|
16: Coin switch
|
|
17: P1 start
|
|
18: P1 up
|
|
19: P1 down
|
|
20: P1 left
|
|
21: P1 right
|
|
22: NC
|
|
23: P1 left select
|
|
24: P1 right select
|
|
25: NC
|
|
26: NC
|
|
27: NC
|
|
28: GND
|
|
```
|
|
|
|
### Bottom side pinout
|
|
|
|
```text
|
|
1: GND
|
|
2: GND
|
|
3: NC
|
|
4: NC
|
|
5: NC
|
|
6: +12V
|
|
7: NC
|
|
8: NC
|
|
9: NC
|
|
10: NC
|
|
11: NC
|
|
12: Video green
|
|
13: Video sync
|
|
14: Service switch
|
|
15: NC
|
|
16: NC
|
|
17: P2 start
|
|
18: P2 up
|
|
19: P2 down
|
|
20: P2 left
|
|
21: P2 right
|
|
22: NC
|
|
23: P2 select left
|
|
24: P2 select right
|
|
25: NC
|
|
26: NC
|
|
27: GND
|
|
28: GND
|
|
```
|
|
|
|
## Pinout secondary 28-pin connector
|
|
|
|
This 28-pin connector is the same as the primary connector but does not
|
|
follow the JAMMA pinout specification.
|
|
|
|
The follow hardware is connected on this connector:
|
|
|
|
* +5V power source
|
|
* Serial cable to EXT I/O
|
|
* Lights I/O cable to AMP box
|
|
|
|
### Top side pinout
|
|
|
|
```text
|
|
1: NC
|
|
2: NC
|
|
3: +5V (red)
|
|
4: NC
|
|
5: Jumper cable (brown) -> Connects to bottom pin 6
|
|
6: NC
|
|
7: EXT I/O serial TX (purple)
|
|
8: NC
|
|
9: NC
|
|
10: NC
|
|
11: NC
|
|
12: NC
|
|
13: NC
|
|
14: NC
|
|
15: NC
|
|
16: NC
|
|
17: NC
|
|
18: NC
|
|
19: NC
|
|
20: NC
|
|
21: NC
|
|
22: NC
|
|
23: NC
|
|
24: Lights P2 cabinet button lights (yellow-grey)
|
|
25: Lights P1 halo up (light blue)
|
|
26: Lights P2 halo down (grey)
|
|
27: GND for +5V (black)
|
|
28: NC
|
|
```
|
|
|
|
### Bottom side pinout
|
|
|
|
```text
|
|
1: NC
|
|
2: NC
|
|
3: NC
|
|
4: NC
|
|
5: NC
|
|
6: Jumper cable (brown) -> Connects to top pin 5
|
|
7: EXT I/O serial RX (grey)
|
|
8: EXT I/O serial GND (black)
|
|
9: NC
|
|
10: NC
|
|
11: NC
|
|
12: NC
|
|
13: NC
|
|
14: NC
|
|
15: NC
|
|
16: NC
|
|
17: NC
|
|
18: NC
|
|
19: NC
|
|
20: NC
|
|
21: NC
|
|
22: NC
|
|
23: Lights P1 cabinet button lights (purple-grey)
|
|
24: Lights P2 halo up (green)
|
|
25: Lights P1 halo down (purple)
|
|
26: Lights GND (black)
|
|
27: NC
|
|
28: NC
|
|
```
|
|
|
|
## Lights I/O connector
|
|
|
|
Lights I/O connector that goes into the AMP box.
|
|
Pintout order: looking at the front of the connector, left to right:
|
|
|
|
```text
|
|
| |--| |
|
|
|-----------------|
|
|
|1 2 3 4 5 6 7 8 9|
|
|
|-----------------|
|
|
|
|
1: Earth (yellow-green)
|
|
2: P2 halo down (grey)
|
|
3: P1 halo down (purple)
|
|
4: P1 halo up (light blue)
|
|
5: P2 halo up (green)
|
|
6: P2 cabinet button lights (yellow-grey)
|
|
7: P1 cabinet button lights (purple-grey)
|
|
8: NC
|
|
9: GND (black)
|
|
```
|
|
|
|
## EXT I/O serial connector
|
|
|
|
Serial connector going to the EXT I/O board.
|
|
Pintout order: looking at the front of the connector, left to right:
|
|
|
|
```text
|
|
| |
|
|
|-----|
|
|
|1 2 3|
|
|
|-----|
|
|
|
|
1: GND (black)
|
|
2: TX (purple)
|
|
3: RX (grey)
|
|
```
|
|
|
|
## Adapter secondary JAMMA connector to "classic" DDR wiring
|
|
|
|
With the secondary JAMMA connector being propriatary to the Dancing
|
|
Stage Fusion cabinet, you need a "breakout" adapter that splices
|
|
the JAMMA connector into the following separate connectors:
|
|
|
|
* `EHR-5` connector to COM1 on the PCB for the EXTIO
|
|
* +5V supply, likely via a 2-pin connector that works with your
|
|
cabinet's internal power infrastructure
|
|
* `XMP-11V` connector to PORT1 on the PCB for lights
|
|
|
|
Note: Bass lights, P1/P2 pad lights as well as sensor multiplexing
|
|
is handled by the EXTIO board.
|
|
|
|
### COM1 breakout
|
|
|
|
Pinout for the `EHR-5` connector breaking out of the JAMMA connector.
|
|
|
|
Pintout order for `EHR-5`: looking at the front of the connector,
|
|
left to right:
|
|
|
|
```text
|
|
| |
|
|
|---------|
|
|
|1 2 3 4 5|
|
|
|---------|
|
|
|
|
1: GND (black)
|
|
2: NC
|
|
3: NC
|
|
4: RX (grey)
|
|
5: TX (purple)
|
|
```
|
|
|
|
Mapping for breakout cable:
|
|
|
|
```text
|
|
JAMMA top: 7 -> EHR-5: 5
|
|
JAMMA bottom: 7 -> EHR-5: 4
|
|
JAMMA bottom: 8 -> EHR-5: 1
|
|
```
|
|
|
|
### Lights connector breakout
|
|
|
|
Pinout for the `XMP-11V` connector breaking out of the JAMMA connector.
|
|
|
|
Pintout order for `XMP-11V`: looking at the front of the connector,
|
|
left to right:
|
|
|
|
```text
|
|
| |--| |
|
|
|-----------------------|
|
|
|1 2 3 4 5 6 7 8 9 10 11|
|
|
|-----------------------|
|
|
|
|
1: NC
|
|
2: P1 halo up
|
|
3: P1 halo down
|
|
4: P2 halo up
|
|
5: P2 halo down
|
|
6: GND
|
|
7: NC
|
|
8: NC
|
|
9: P2 cabinet button lights
|
|
10: P1 cabinet button lights
|
|
11: GND
|
|
```
|
|
|
|
Mapping for breakout cable:
|
|
|
|
```text
|
|
JAMMA top: 24 -> XMP-11V: 9
|
|
JAMMA top: 25 -> XMP-11V: 2
|
|
JAMMA top: 26 -> XMP-11V: 5
|
|
JAMMA bottom: 23 -> XMP-11V: 10
|
|
JAMMA bottom: 24 -> XMP-11V: 4
|
|
JAMMA bottom: 25 -> XMP-11V: 3
|
|
JAMMA bottom: 26 -> XMP-11V: 6 + 11
|
|
```
|